Difficulté
Moyen
Durée
6 heure(s)
Coût
5 EUR (€)
Description
Making a 4-5 seat bench from recycled skis
Introduction
- The first step is to collect pallets and skis, for example, from a waste disposal centre or DIY shop.
- The second is to dismantle the pallets and ski bindings. Only skis without visible bindings or screws are used.
- Once the material is ready, the third step is to cut the boards to the required sizes.
- The fourth and final step is to assemble the benches, finishing by sanding down any rough edges to give a cleaner finish.
A bench is built with 3 legs (only 2 legs pose problems of solidity as the skis are very flexible).
You can attach between 4 and 6 skis: 4 with 3 skis for the seat and 1 for lateral strength. 6 with 4 skis for the seat and 2 for lateral strength (see image below)
Possible alternative:
The skis on the seat can be replaced by a snowboard!
Matériaux
- Pallets (or solid wood planks)
- Nails x36 (minimum)
- About thirty 5 x 50 mm screws
- 6 skis (minimum 4)
Outils
- crowbar or palette knife
- Hammer to remove the paint
- Measuring tape
- Hand saw or jigsaw
- Screw gun
- Drill
- (Optional) Sanding block or sander
Étape 1 - Recovery of pallets and skis
Plan this search in advance of the workshop: skis can be collected from waste collection centres, and pallets from the depots of supermarkets and DIY shops.
Étape 2 - Remove pallets and ski bindings:
To dismantle a pallet, take it slowly and don't force it, otherwise you risk damaging the boards. Place the crowbar in the gaps, and tap the crowbar with the sledgehammer so that it fits into the gap, repeating the process in different places until you feel the boards coming loose. Note that if you break the ends of some of the boards, it's not a big deal, as some of them will be cut off later.
Suivre le désossement de palettes suivant :
- Commencer pour les planches 2 et 4 du dessus
- Retourner la palette et enlever les blocs des planches 1, 3 et 5
- Retirer les planches liées aux blocs
- Taper sur les clous des planches 1, 3, 5 pour les faire sortir.
- Méthode similaire sur ce tutoriel (https://www.youtube.com/watch?v=tQnQkdUS3yo)
Étape 3 - Découpe des planches :
- Larges : Pour les planches verticales des pieds
- Fines : Les traverses des pieds
Fabrication d’un pied :
- Petite traverse x2 ( Coupe droite, longueur 30cm )
- Grande traverse x4 (Coupe droite Longueur 45cm)
- Traverse “support” : 30x15 cm
Donc pour un banc (= 3 pieds):
- Petite traverse x6 (jaune sur la photo)
- Grande traverse x12 (orange sur la photo)
- Traverse “support” x3 (vert sur la photo)
Étape 4 - Assemblage des pieds
Etape 1 : Visser les petites traverses sur les grandes traverses antérieures
Etape 2 : Visser les grandes traverses postérieures sur l’assemblage (petite traverse + grande traverse antérieur) afin d’avoir les pieds
Etape 3 : Visser la traverse supérieure sur le haut du pied
Étape 5 - Assemblage des skis sur les pieds
Etape 1 : Visser les skis centraux sur les pieds.
Etape 2 : Puis fixer un ski latéral par côté (à ~ 10 cm du bas)
Draft
Français
English
Deutsch
Español
Italiano
Português