Concentrateurs solaires/en

Aurelpere

https://wiki.lowtechlab.org/wiki/Concentrateurs_solaires/en

Dernière modification le 02/12/2024

Difficulté

Medium Moyen

Durée

6 hour(s) heure(s)

Coût

80 EUR (€)

Description

Solar concentrators building (reflector+plaster or parabolic antenna)

Sommaire

solaire, energie, énergie, renouvelables, concentrateur, reflecteur, solaire thermique

---

Introduction

I first built solar concentrators to try to power a mini stirling engine ("scientific toy"). You can see it on the video in step 3 and in the other tutorial i made here: Stirling Engine.

The exercise is not so simple, so i decided to make a dedicated tutorial.

For the mini stirling engine, you need a high degree of concentration (2cmx4cm) and it is more appropriate to use a fresnel lens.

Matériaux

made from parabolic antenna

- parabolic antenna (40cm to a few meters) in recycling shop or on internet: 10€

made from plaster

- yoga baloon with a diameter two times the diameter wanted

- plaster : 15kg for a 80cm reflector: 20€

- sand : 4 trowels for a bucket of plaster

- pane glue: 4 trowels for a bucket of plaster 10€

- reflector tape: 20€/m2

https://www.solarbrother.com/categorie-produit/reflecteur-solaire

- super glue (20g) 5€

- paint tape 10€

- microphone leg 5€

Outils

Étape 1 - building a piece of sphere from plaster

If you choose the first option to recycle a parabolic antenna, you can skip step1 and read below.

Choosing a plaster piece of sphere or a parabolic antenna may depend on the wanted focal of the concentrator (see video in step 3).

The focal is the distance from the center of the concentrator to where the sun rays converge.

The focal of plaster piece of sphere is smaller than the parabolic antenna one.

Initially, i have made tests with pieces of sphere to try to obtain a higher degree of solar concentration, but the results show approximately the same surface of concentration (at equal diameter).

Mixing plasters

We can fin specific plaster for thin mouldings. In doubt, take several types of plasters and stir together.

Anyway, we add a bit of sand and pane glue to make the plaster more solid.

Stir in the proportion 4 trowels of pane glue and sand for a bucket of plaster.

Stir with water, and spread on the inflated and stabilized yoga baloon.

In order to manipulate and orientate the reflector, we can use a microphone leg. Unfortunately, the microphone leg is difficult to glue on the plaster, so be mindful to stick the micro leg in the plaster when it's drying.

NB: for a 80cm concentrator, it's a bit heavy for a standard micro leg, so be mindful to check the sizing so it is stable.

The grey baloon is 75cm diameter and the orange baloon is 150cm.

Étape 2 - reflector sticking

Initially, i made a try with a small concentrator with bits of mirror, but it's not very efficient.

We can find flexible reflector tape at solar brother (see link in material) that is efficient and costs 20€/m2.

There are two points where you have to pay attention to stick the reflector:

-We want to avoid warping

-if you have a plaster molding, the reflector tape sticks badly

We will proceed cutting out triangles with a thin base to avoid warping when sticked. On my tries, i have a 7cm base for the 80cm diameter concentrator and a 10cm base for the 40cm diameter concentrator.

Pour que ca colle sur le platre, on aplique d'abbord du scotch peinture sur toute la surface du reflecteur.

Dans tous les cas, ajouter de la super glue à la surface adhésive car ca se décolle assez rapidement sinon.

Étape 3 - mesure de puissance

Pour l'instant je n'ai pas fait de mesure d'évaporation d'eau. J'essaierai d'en faire quand j'aurai le temps.

En attendant voici des vidéos où on peut estimer la focale des reflecteurs et voir des planches commencer un processus de combustion (version parabole pour la vidéo avec le moteur stirling miniature au mois de juillet et version bout de sphere platre 80cm pour la video où le reflecteur est posé au sol au mois de novembre)

en fr 1 Published