(Page créée avec « Install and secure the belt buckle on the strap. ») |
(Page créée avec « At '''10 cm''' from the edge, fold one end of the strap and drill a hole in the middle. This hole will allow the tongue to pass through. Install the buckle and pass the ro... ») |
||
| Ligne 44 : | Ligne 44 : | ||
{{Tuto Step | {{Tuto Step | ||
|Step_Title=Install and secure the belt buckle on the strap. | |Step_Title=Install and secure the belt buckle on the strap. | ||
| − | |Step_Content= | + | |Step_Content=At '''10 cm''' from the edge, fold one end of the strap and drill a hole in the middle. This hole will allow the tongue to pass through. |
| − | + | Install the buckle and pass the rod through the hole. Fold the tire around the buckle | |
| − | + | To hold the buckle in place, create a hole about one centimeter from the buckle in the middle, then rivet, adding a washer to hold the rivet (or use a pop rivet). | |
| − | + | If the tire is thick, drill two holes on either side of the strap. | |
|Step_Picture_00=Ceinture_en_pneu_de_v_lo_IMG_7964.jpeg | |Step_Picture_00=Ceinture_en_pneu_de_v_lo_IMG_7964.jpeg | ||
|Step_Picture_01=Ceinture_en_pneu_de_v_lo_IMG_7966.jpeg | |Step_Picture_01=Ceinture_en_pneu_de_v_lo_IMG_7966.jpeg | ||
Version du 15 novembre 2024 à 15:28
Dernière modification le 15/11/2024
Difficulté
Moyen
Durée
30 minute(s)
Coût
0.50 EUR (€)
Description
DIY bike tire belt
Sommaire
Introduction
In this DIY, we will explain how to creat a belt made from an old bike tire.
Matériaux
- Bike tire (one per belt) - belt buckle or wire - bike inner tube - screw rivet (or pop rivet)
Outils
- Scissors - Cutter - Hole punch - Metal pliers - Riveter (if using pop rivets)
Étape 1 - Creat the belt strap
Cut the part of the tire which will constitute the belt,to the desired length, taking a model from an old belt or taking its waist measurement and adding approximately 15 cm.
Étape 2 - Creat the belt buckle
Re-use a buckle from an old belt.
or
Create the buckle and pin of the belt from a metal rod using metal pliers.
If the buckle is not welded, the rod junction point must not be centered, otherwise the barb will come out.
Étape 3 - Install and secure the belt buckle on the strap.
At 10 cm from the edge, fold one end of the strap and drill a hole in the middle. This hole will allow the tongue to pass through. Install the buckle and pass the rod through the hole. Fold the tire around the buckle To hold the buckle in place, create a hole about one centimeter from the buckle in the middle, then rivet, adding a washer to hold the rivet (or use a pop rivet). If the tire is thick, drill two holes on either side of the strap.
Étape 4 - Installer et fixer le passant de la ceinture
- Installer le passant en chambre à air, en le faisant glisser le long de la sangle.
- Pour éventuellementfixer le passant, mettre un dernier rivet (avec rondelle) après la boucle pour bien maintenir cette dernière.
Étape 5 - Créer les crans de la ceinture
Prendre les mesures pour déterminer l'emplacement des crans de la ceinture.
Faire des trous à la pince perforatrice pour former les crans de la ceinture.
La ceinture est prête !!
Draft
Français
English
Deutsch
Español
Italiano
Português