Dessalinisateur solaire autonome/en

L'eauTech

https://wiki.lowtechlab.org/wiki/Dessalinisateur_solaire_autonome/en

Dernière modification le 05/07/2024

Difficulté

Hard Difficile

Durée

20 day(s) jour(s)

Coût

300 EUR (€)

Description

A project by engineering students to build a low-tech solar watermaker to help disadvantaged communities.

Sommaire

dessalinisateur, Solaire, eau, potable, low-tech, en fr 1

---

Introduction

L'EauTech is a project run by six students from the Ecole Centrale de Lille in collaboration with the Gold Of Bengal association. The aim of the project is to build a low-tech solar watermaker, based on two projects already carried out at the Ecole Centrale de Lille: the Opensol project, which created a low-tech solar concentrator, and the Delta project, which created a low-tech watermaker.

You can find and download a summary of this tutorial in PDF format by clicking on this link: https://drive.google.com/open?id=1aqvStMdIfSuhj4bioxSa0Zk8wiuJO1vL .

Matériaux

1. Solar concentrator

1.1. Frame

• Strong wooden board, minimum size 1x2m

1.2 Main reflector

1.2.1. Main reflector support

• Wooden board minimum size 0.9x2m

1.2.2. Mirrors

• Around 35 sheets of mirrors measuring 10x80cm

OR

• Around 35 aluminium sheets, minimum size 10x80cm
• A self-adhesive mirror to cut out, approx. 0.1x1m (if possible)

1.3. Secondary reflector

1.3.1. Copper pipe and reflector support

• 2 wooden battens, 2.4m long and 27x27mm in cross-section
• Wooden board (thickness: approx. 5mm, surface: enough to make two slabs approx. 8x8cm)
• 2 clamps diameter 28mm
• 6 screws
• 28mm diameter copper pipe, 1m long
• 2mm thick sheet metal

1.3.2. Secondary reflector and copper pipe

• PVC tube: 1m long and 10cm in diameter
• Soda cans
• Black paint

2. Watermaker

2.1. Evaporation tank

2.1.1. Frame

• 6 stainless steel sheets 2mm thick (2 sheets 15cmx4cm, 2 sheets 1mx1cm, 1 sheet 1mx1cm, 1 sheet 1.02mx6cm)

2.1.2. Stages

• 2 stainless steel sheets 2mm thick: 1mx3.6cm

2.1.3. Copper pipe

• 14mm diameter copper tube 1m long

2.2 Condensation tank

2.2.1. Frame

• 2mm-thick stainless steel sheet measuring at least 200x2100mm

2.2.2. Copper pipe

• 14mm diameter copper tube 2,5m long

2.2.2.1. Copper condensing coil 2.2.2.2. Copper water inlet pipe 2.2.2.3. Copper water outlet pipe

2.2.3. Cover

• 8 screws 6mm diameter with washers and nuts
• 2mm thick stainless steel sheet: 250x250mm

3. Total circuit

3.1 Circuit-closing pipes

• 20 rubber seals
• Valve
• 5 flexible tubes 1m or 50 cm to close the circuit
• Any fittings

3.2. Pump

• Oil pump
• Vegetable oil

Outils

• Screws
• Drills
• Saw
• Scissors
• Measuring tape
• Wood glue
• Strong glue for all materials
• Pencil
• Screwdrivers
• Welding machine
• Hacksaw

Étape 1 - Nomenclature

1 Solar concentrator

  1.1 Frame
  1.2 Main reflector
     1.2.1 Support for main reflector
     1.2.2 Mirrors
  1.3 Secondary reflector
     1.3.1 Support for secondary reflector
     1.3.2 Secondary reflector and copper pipe

2 Watermaker

  2.1 Evaporation tank
     2.1.1 Frame
     2.1.2 Stages
     2.1.3 Copper pipe
  2.2 Condensation tank
     2.2.1 Frame
     2.2.2 Copper pipes
        2.2.2.1 Copper condensing coil
        2.2.2.2 Copper water inlet pipe
        2.2.2.3 Copper water outlet pipe
  2.2.3 Cover

3 Total circuit

  3.1 Circuit closing pipes4
  3.2 Pump

Étape 2 - General operating principle

The system can be split into two sub-systems: the solar concentrator 1 and the watermaker 2.

In the solar concentrator 1, the sun's rays are reflected by the main reflector 1.2 and the secondary reflector 1.3 towards a copper tube 1.3.2 in which a heat transfer fluid (oil) circulates. This fluid is then heated until it boils. It circulates in a closed circuit thanks to a pump 3.2.

This circuit goes through an evaporation tank 2.1 filled with dirty water, which is heated to boiling point by the heat transfer fluid. This water vapour then goes through two successive distillation stages 2.1.2 in the evaporation tank 2.1, before reaching the condensation tank 2.2 in which the water vapour is condensed by a coil 2.2.2.1 through which it travels before emerging as clean liquid water.

Étape 3 - Solar concentrator 1 - Presentation

• Name of the different parts of the solar concentrator 1
• Material: wood
• Copper tubes
• Mirrors (or aluminium plates)

Étape 4 - Solar concentrator 1 - Main reflector 1.2 - Step 1

Step 1: Frame 1.1

• Cut the frame 1.1 out of the strong wooden board: 1mx2m

Étape 5 - Solar concentrator 1 - Main reflector 1.2 - Step 2

Step 2: Main reflector brackets 1.2.1

• Cut out the 3 1.2.1 supports for the main reflector using wooden planks.
• For the parabolic shape: see dimensions in the table.

Étape 6 - Solar concentrator 1 - Main reflector 1.2 - Step 3

Step 3: Mirrors 1.2.2

• Main reflector 1.2: cut the mirror plates 1.2.2 into rectangular shapes (dimensions from previous table).
• Fix the plates 1.2.2 with glue to the support 1.2.1 and check that they are correctly oriented: the sun's rays should converge towards a pipe located at a height of 80cm.

Note: The 1.2.2 mirror can be replaced by an aluminium plate that can be covered with self-adhesive mirror.

Étape 7 - Solar concentrator 1 - Pipe support 1.3.1 - Step 1

Step 1: Cutting the battens

• Cut the battens into four pieces approximately 65 cm long.
• Cut inclined planes at the end of the 4 pieces so that they can be glued together 2 by 2 (see photo). After gluing, the top should be 80cm above the frame.
• Cut other inclined surfaces on the other side of the 4 pieces so that they can be fixed to the 1.1 frame.

Étape 8 - Solar concentrator 1 - Pipe support 1.3.1 - Step 2

Step 2: Secondary reflector support 1.3.1 and clamps

• Grind the cut surfaces to make the glue more effective.
• Glue the cleats C from the previous step in pairs. Board B must be 80cm above the frame.
• Screw the two boards B to the battens C (see photo) using the clamp support A.

Étape 9 - Solar concentrator 1 - Pipe support 1.3.1 - Step 4

Step 4: Consolidation

• Using the off-cuts of battens, cut pieces and glue them to the supports, taking care to sand them as before, so as to consolidate the structure.

Étape 10 - Solar concentrator 1 - Pipe support 1.3.1 - Step 5

Step 5: Screwing

• All that remains is to screw the two pieces of the pipe support structure 1.3.1 to the frame 1.1 from underneath the structure.

Étape 11 - Solar concentrator 1 - Secondary reflector 1.3 - Presentation

The secondary reflector 1.3 reflects light rays not intercepted by the copper tube 1.3.2 back onto it. It is located above the tube 1.3.2.

Étape 12 - Solar concentrator 1 - Main reflector 1.3 - Step 1

Step 1: Cutting the PVC pipe

The PVC tube is what supports the secondary reflector 1.3. It holds the soda cans that reflect the light rays.

• Cut the PVC pipe in half lengthways.
• Colour the outside of the PVC pipe black with paint.

Étape 13 - Solar concentrator 1 - Main reflector 1.3 - Step 2

Step 2: Cutting and gluing the cans

As the cans are made of aluminium, the inside of the can proved to be a good alternative for reflecting light rays.

• Cut the cans into rectangles 9cm wide, there are no length constraints for the other sides.
• Fold in half widthways to make two parts 4.5cm wide.
• Glue the cans into the PVC tube (they will have a rounded W shape) using strong glue.

• Note: you can stick self-adhesive mirrors in the cans to improve reflection.

Étape 14 - Watermaker 2 - Presentation

• Name of the different parts of the watermaker 2
• Material: steel
• Copper tubes
• The condensation tank 2.2 is used to store brackish water before the evaporation tank 2.1. In this tank, the steam created by the evaporation tank 2.1 circulates in a coil 2.2.2.1.
• The evaporation vat 2.1, consisting of 2 stages 2.1.2, is used to convert brackish water into steam. The vapour created circulates through a coil 2.2.2.1 in the condensation tank 2.2 in order to cool it and convert it into a liquid state.
• Desalinated water is thus obtained.

Étape 15 - Watermaker 2 - Evaporation tank 2.1 - Step 1

Step 1: Manufacture of the frame 2.1.1

• Cut the metal sheet into 6 rectangles (2 rectangles of 4cm*15cm; 2 of 1m*15cm; 1 of 1m*4cm; 1 of 6cm*1.02m). See photo.
• Fold at right angles over 1 cm as shown in the dotted lines in the photo, then make holes in the folded part to fit the screws.

• Note 1: Be careful to ensure that the walls of tank 2.1 are watertight (soldering is required)!
• Note 2: Be careful to seal between the lid and the folded walls (use a bicycle inner tube, for example, before screwing)!

Étape 16 - Watermaker 2 - Evaporation tank 2.1 - Step 2

Stage 2: Manufacture of stages 2.1.2

• Cut out 2 trays measuring 99.6cm*3.6cm.
• Add material by welding to the side walls of vat 2.1 so that the trays can be placed on them (see photo for the height of the 2 trays and therefore the height of the 2 additions of material).
• Drill 5 cm diameter holes at one end of each tray (so that steam can circulate through all the levels) and place the 2 trays in vat 2.1 with their holes located at opposite ends.

Étape 17 - Watermaker 2 - Evaporation tank 2.1 - Step 3

Step 3: Making the 3 holes for the copper pipes inlet to the condensing coil 2.2.2.1 and pipe 2.2.2.3 which passes through the tank 2.1 at the bottom.

• In the 2 side walls furthest from tank 2.1: make a 14 mm diameter hole (see photo for position) in the bottom tier for pipe 2.2.2.3.
• In one of these same side walls, make a 14 mm diameter hole in the top tier (for the 2.2.2.1 pipe used to evacuate the steam).
• Solder to make a seal between the pipes and the tank!

Étape 18 - Watermaker 2 - Evaporation tank 2.2 - Step 1

Step 1: Cutting the sheet into 5 sections

• 5-sided cut-out

   * Base side: 200x200mm
   * 4 side panels: 200x355mm

• Fold the side faces on top to create edges for screwing on a lid (using the same system as in the previous step).
• Welding of the base and 4 sides

Étape 19 - Watermaker 2 - Evaporation tank 2.2 - Step 2

Step 2 : Holes

Four holes to drill:

• A water inlet hole from the storage tank, which accommodates a flow regulator (such as a flush valve for autonomous use, but a simple manual valve may suffice). This hole should be at the top of the tank. The 2.2.2.2 pipe passes through it.
• An outlet hole for brackish water preheated by steam condensation, at the bottom of tank 2.2, towards evaporation tank 2.1. Pipe 2.2.2.3 passes through.
• A steam inlet hole from the evaporation tank 2.1 (condensation coil inlet 2.2.2.1), located below the water level in tank 2.2.
• A drinking water outlet hole (condensing coil outlet 2.2.2.1), lower than the previous hole.

• Note: these holes must be made in relation to the other parts of the prototype (particularly for the condensation coil 2.2.2.1 where it is advisable to manufacture it before drilling the holes: see next step).

• See image where the brackish water outlet hole is not shown (water inlet: top right and the 2 ends of the condensing coil 2.2.2.1 are top left and bottom right).

Étape 20 - Watermaker 2 - Evaporation tank 2.2 - Step 3

Step 3: Condensing coil 2.2.2.1 (where the steam condenses)

• Entourer le tube de cuivre 2.2.2.1 d'un ressort rigide (il permet d'obtenir une forme circulaire)
• Si le cuivre n'est pas recuit, il faut le chauffer jusqu'à ce qu'il atteigne une couleur rouge et le plonger dans de l'eau froide immédiatement.
• Il faut ensuite lui donner une forme hélicoïdale en l'enroulant petit à petit autour d'un cylindre.
• Insérer le serpentin 2.2.2.1 dans la cuve 2.2 à travers les 2 trous précédemment fait

Étape 21 - Dessalinisateur 2 - Cuve de condensation 2.2 - Etape 4

Etape 4: Couvercle 2.3 de la cuve 2.2

• Percer au moins 8 trous sur les rebords de la cuve 2.2 pour les vis qui fixeront le couvercle 2.3.
• Découper une tôle carré de 250x250mm qui fera office de couvercle 2.3 et y percer au moins 8 trous correspondants aux précédents afin de pouvoir visser ce couvercle;
• Une chambre à air de vélo peut être insérée entre les rebords de la cuve 2.2 et le couvercle 2.3 pour une meilleure étanchéité.

Étape 22 - Circuit total 3

Les deux parties principales étant construites, il ne reste plus qu’à fermer le circuit où circulera le fluide caloporteur ! Ce fluide caloporteur est une huile végétale qui circulera grâce à la pompe 3.2 intégrée au circuit. Privilégier des tuyaux 3.1 bien isolés thermiquement (isoler soi-même au besoin), flexibles (pour pouvoir déplacer facilement le prototype).

Étape 23 - Pompe 3.2

Pour le choix de la pompe 3.2, il faut bien faire attention à utiliser une pompe à huile. Une telle pompe peut être une pompe de récupération et peut se trouver sur des motos ou des voitures ou toute autre machine dont le fonctionnement nécessite une pompe à huile.

Published