(Page créée avec « Re-use a buckle from an old belt. ») |
(Mise à jour pour être en accord avec la nouvelle version de la source de la page) |
||
| (11 révisions intermédiaires par un autre utilisateur non affichées) | |||
| Ligne 36 : | Ligne 36 : | ||
|Step_Content=Re-use a buckle from an old belt. | |Step_Content=Re-use a buckle from an old belt. | ||
| − | + | or | |
| − | + | Create the buckle and pin of the belt from a metal rod using metal pliers. | |
| − | + | If the buckle is not welded, the rod junction point must not be centered, otherwise the barb will come out. | |
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
| − | |Step_Title= | + | |Step_Title=Install and secure the belt buckle on the strap. |
| − | |Step_Content= | + | |Step_Content=At '''10 cm''' from the edge, fold one end of the strap and drill a hole in the middle. This hole will allow the tongue to pass through. |
| − | + | Install the buckle and pass the rod through the hole. Fold the tire around the buckle | |
| − | + | To hold the buckle in place, create a hole about one centimeter from the buckle in the middle, then rivet, adding a washer to hold the rivet (or use a pop rivet). | |
| − | + | If the tire is thick, drill two holes on either side of the strap. | |
|Step_Picture_00=Ceinture_en_pneu_de_v_lo_IMG_7964.jpeg | |Step_Picture_00=Ceinture_en_pneu_de_v_lo_IMG_7964.jpeg | ||
|Step_Picture_01=Ceinture_en_pneu_de_v_lo_IMG_7966.jpeg | |Step_Picture_01=Ceinture_en_pneu_de_v_lo_IMG_7966.jpeg | ||
| Ligne 53 : | Ligne 53 : | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
| − | |Step_Title= | + | |Step_Title=Install and secure the belt loop |
| − | |Step_Content= | + | |Step_Content=Install the inner tube loop, by sliding it along the strap. |
| − | + | To possibly fix the loop, put a last screw rivet (or pop rivet) after the buckle to hold it securely. | |
|Step_Picture_00=Ceinture_en_pneu_de_v_lo_IMG_7979.jpeg | |Step_Picture_00=Ceinture_en_pneu_de_v_lo_IMG_7979.jpeg | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
| − | |Step_Title= | + | |Step_Title=Create the belt notches |
| − | |Step_Content= | + | |Step_Content=Take measurment to choose where to put the belt notches. |
| − | + | Make holes with the hole punch pliers to form the notches of the belt. | |
| − | + | The belt is ready!! | |
|Step_Picture_00=Ceinture_en_pneu_de_v_lo_IMG_7978.jpeg | |Step_Picture_00=Ceinture_en_pneu_de_v_lo_IMG_7978.jpeg | ||
}} | }} | ||
| Ligne 76 : | Ligne 76 : | ||
}} | }} | ||
{{Tuto Status | {{Tuto Status | ||
| − | |Complete= | + | |Complete=Published |
}} | }} | ||
Version actuelle datée du 15 novembre 2024 à 15:35
Dernière modification le 15/11/2024
Difficulté
Moyen
Durée
30 minute(s)
Coût
0.50 EUR (€)
Description
DIY bike tire belt
Introduction
In this DIY, we will explain how to creat a belt made from an old bike tire.
Matériaux
- Bike tire (one per belt) - belt buckle or wire - bike inner tube - screw rivet (or pop rivet)
Outils
- Scissors - Cutter - Hole punch - Metal pliers - Riveter (if using pop rivets)
Étape 1 - Creat the belt strap
Cut the part of the tire which will constitute the belt,to the desired length, taking a model from an old belt or taking its waist measurement and adding approximately 15 cm.
Étape 2 - Creat the belt buckle
Re-use a buckle from an old belt.
or
Create the buckle and pin of the belt from a metal rod using metal pliers.
If the buckle is not welded, the rod junction point must not be centered, otherwise the barb will come out.
Étape 3 - Install and secure the belt buckle on the strap.
At 10 cm from the edge, fold one end of the strap and drill a hole in the middle. This hole will allow the tongue to pass through. Install the buckle and pass the rod through the hole. Fold the tire around the buckle To hold the buckle in place, create a hole about one centimeter from the buckle in the middle, then rivet, adding a washer to hold the rivet (or use a pop rivet). If the tire is thick, drill two holes on either side of the strap.
Étape 4 - Install and secure the belt loop
Install the inner tube loop, by sliding it along the strap. To possibly fix the loop, put a last screw rivet (or pop rivet) after the buckle to hold it securely.
Étape 5 - Create the belt notches
Take measurment to choose where to put the belt notches.
Make holes with the hole punch pliers to form the notches of the belt.
The belt is ready!!
Published
Français
English
Deutsch
Español
Italiano
Português