(Page créée avec « A bench is built with 3 legs (only 2 legs pose problems of solidity as the skis are very flexible). ») |
(Page créée avec « <u>Step 2</u>: Then attach one side ski per side (~ 10 cm from the bottom) ») |
||
(25 révisions intermédiaires par le même utilisateur non affichées) | |||
Ligne 22 : | Ligne 22 : | ||
A bench is built with 3 legs (only 2 legs pose problems of solidity as the skis are very flexible). | A bench is built with 3 legs (only 2 legs pose problems of solidity as the skis are very flexible). | ||
− | + | You can attach between 4 and 6 skis: 4 with 3 skis for the seat and 1 for lateral strength. 6 with 4 skis for the seat and 2 for lateral strength (see image below) | |
− | <u> | + | <u>Possible alternative:</u> |
− | + | The skis on the seat can be replaced by a snowboard! | |
}} | }} | ||
{{Materials | {{Materials | ||
− | |Material=* | + | |Material=* Pallets (or solid wood planks) |
− | * | + | * Nails x36 (minimum) |
− | * | + | * About thirty 5 x 50 mm screws |
* 6 skis (minimum 4) | * 6 skis (minimum 4) | ||
− | |Tools=* | + | |Tools=* crowbar or palette knife |
− | * | + | * Hammer to remove the paint |
− | * | + | * Measuring tape |
− | * | + | * Hand saw or jigsaw |
− | * | + | * Screw gun |
− | * | + | * Drill |
− | * ( | + | * (Optional) Sanding block or sander |
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
− | |Step_Title= | + | |Step_Title=Recovery of pallets and skis |
− | |Step_Content= | + | |Step_Content=Plan this search in advance of the workshop: skis can be collected from waste collection centres, and pallets from the depots of supermarkets and DIY shops. |
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
− | |Step_Title= | + | |Step_Title=Remove pallets and ski bindings: |
− | |Step_Content= | + | |Step_Content=To dismantle a pallet, take it slowly and don't force it, otherwise you risk damaging the boards. Place the crowbar in the gaps, and tap the crowbar with the sledgehammer so that it fits into the gap, repeating the process in different places until you feel the boards coming loose. Note that if you break the ends of some of the boards, it's not a big deal, as some of them will be cut off later. |
− | + | Follow the boning of the following pallets: | |
− | * | + | * Start with boards 2 and 4 from the top |
− | * | + | * Turn the pallet over and remove the blocks from planks 1, 3 and 5 |
− | * | + | * Remove the boards attached to the blocks |
− | * | + | * Tap the nails on boards 1, 3 and 5 to remove them. |
− | * | + | * Similar method on this tutorial (<u>https://www.youtube.com/watch?v=tQnQkdUS3yo</u>) |
|Step_Picture_00=Bancs_en_ski_Banc_Ski-palette.png | |Step_Picture_00=Bancs_en_ski_Banc_Ski-palette.png | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
− | |Step_Title= | + | |Step_Title=Cutting the boards : |
− | |Step_Content=* | + | |Step_Content=* Wide: For the vertical foot boards |
− | * | + | * Thin: The crosspieces of the legs |
− | + | Making a stand : | |
− | * | + | * Small crossbar x2 ( Straight cut, length 30cm ) |
− | * | + | * Large crossbar x4 (Straight cut, length 45cm) |
− | * | + | * ''Support'' crosspiece: 30x15 cm |
− | + | So for a bench (= 3 feet): | |
− | * | + | * Small crossbar x6 (yellow on photo) |
− | * | + | * Large crossbar x12 (orange on photo) |
− | * | + | * ''Support'' crossbar x3 (green in photo) |
|Step_Picture_00=Bancs_en_ski_Pied_nonassembl_.jpg | |Step_Picture_00=Bancs_en_ski_Pied_nonassembl_.jpg | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
− | |Step_Title= | + | |Step_Title=Assembly of the feets |
− | |Step_Content=''<u> | + | |Step_Content=''<u>Step 1:</u>'' Screw the small crosspieces onto the large front crosspieces |
− | <u> | + | <u>Step 2</u>: Screw the large rear crosspieces to the assembly (small crosspiece + large front crosspiece) to create the feet. |
− | <u> | + | <u>Step 3</u>: Screw the top crossbar onto the top of the leg |
|Step_Picture_00=Bancs_en_ski_Pied-semi_assembl_.jpg | |Step_Picture_00=Bancs_en_ski_Pied-semi_assembl_.jpg | ||
|Step_Picture_01=Bancs_en_ski_Pied-Mesure.png | |Step_Picture_01=Bancs_en_ski_Pied-Mesure.png | ||
Ligne 95 : | Ligne 95 : | ||
}} | }} | ||
{{Tuto Step | {{Tuto Step | ||
− | |Step_Title= | + | |Step_Title=Assembling the skis on the feet |
− | |Step_Content=<u> | + | |Step_Content=<u>Step 1</u>: Screw the centre skis onto the feet. |
− | <u> | + | <u>Step 2</u>: Then attach one side ski per side (~ 10 cm from the bottom) |
|Step_Picture_00=Bancs_en_ski_Banc_ski-sanspied.jpg | |Step_Picture_00=Bancs_en_ski_Banc_ski-sanspied.jpg | ||
|Step_Picture_01=Bancs_en_ski_Banc-ski_Ttotal.png | |Step_Picture_01=Bancs_en_ski_Banc-ski_Ttotal.png |
Tutorial de Low-tech with Refugees - Low-tech & Réfugiés | Catégories : Habitat
Low-tech with Refugees - Low-tech & Réfugiés
Making a 4-5 seat bench from recycled skis
Making a 4-5 seat bench from recycled skis
Bois, Banc, Ski
A bench is built with 3 legs (only 2 legs pose problems of solidity as the skis are very flexible).
You can attach between 4 and 6 skis: 4 with 3 skis for the seat and 1 for lateral strength. 6 with 4 skis for the seat and 2 for lateral strength (see image below)
Possible alternative:
The skis on the seat can be replaced by a snowboard!
Plan this search in advance of the workshop: skis can be collected from waste collection centres, and pallets from the depots of supermarkets and DIY shops.
To dismantle a pallet, take it slowly and don't force it, otherwise you risk damaging the boards. Place the crowbar in the gaps, and tap the crowbar with the sledgehammer so that it fits into the gap, repeating the process in different places until you feel the boards coming loose. Note that if you break the ends of some of the boards, it's not a big deal, as some of them will be cut off later.
Follow the boning of the following pallets:
Making a stand :
So for a bench (= 3 feet):
Step 1: Screw the small crosspieces onto the large front crosspieces
Step 2: Screw the large rear crosspieces to the assembly (small crosspiece + large front crosspiece) to create the feet.
Step 3: Screw the top crossbar onto the top of the leg
Step 1: Screw the centre skis onto the feet.
Step 2: Then attach one side ski per side (~ 10 cm from the bottom)
en fr 1 Draft
Vous avez entré un nom de page invalide, avec un ou plusieurs caractères suivants :
< > @ ~ : * € £ ` + = / \ | [ ] { } ; ? #