Recherche par propriété

Cette page fournit une simple interface de navigation pour trouver des entités décrites par une propriété et une valeur nommée. D’autres interfaces de recherche disponibles comprennent la page recherche de propriété, et le constructeur de requêtes ask.

Une liste de toutes les pages qui ont la propriété « Step Content » avec la valeur « ''' Module 1 : Solar panel and charge regulator''' 1) Use a black and a red wire, use a wire cutter to remove sleeving from the wires. 2) Solder the red wire on the (+) side of the panel and the black on on the (-) side. The charge regulator has 2 inputs : IN- and IN+ (which are indicated on the component). 3) Solder the red wire (positive) with the IN+ input of the charge regulator and the black wire (negative) with the IN- input ''(image 5)''. '''Module 2 : Battery''' 1) Tape the two cells together for easier soldering 2) Take 2 wires, one red and one black, remove sleeving on their tips on a few centimeters 3) Soldering the 2 cells in parallel : black wire to the negative poles of each cell and red wire on the positive pole of each cell. ''(image 6)'' ''Caution:'' Isolate the welds (e.g. with tape) to avoid short-circuits . '''Module 3 : Voltage regulator and LED''' The voltage regulator has 2 inputs and 2 outputs: Inputs : VIN + and VIN - / Outputs : OUT + and OUT - 1) Take two wires (red and black). 2) Weld the red wire with the VIN+ input of the voltage regulator and the black wire with the VIN- input. The LED has two input wires : one positive and one negative. ''Caution:'' Wire polarity is not indicated on the LED. In order to identify it, use an ohmmeter. The wire is positive when it displays a null value. When it displays a higher value, the wire is negative. 3) Weld the LED's positive wire to the OUT+ output of the voltage regulator and the LED's negative wire to the OUT- output. ''(image 7)'' ». Puisqu’il n’y a que quelques résultats, les valeurs proches sont également affichées.

Affichage de 1 résultat à partir du n°1.

Voir (200 précédentes | 200 suivantes) (20 | 50 | 100 | 250 | 500).

Propriété : Valeur :

Liste de résultats

Batteries recovery + (''' Module 1 : Solar panel and charge regu … ''' Module 1 : Solar panel and charge regulator''' 1) Use a black and a red wire, use a wire cutter to remove sleeving from the wires. 2) Solder the red wire on the (+) side of the panel and the black on on the (-) side. The charge regulator has 2 inputs : IN- and IN+ (which are indicated on the component). 3) Solder the red wire (positive) with the IN+ input of the charge regulator and the black wire (negative) with the IN- input ''(image 5)''. '''Module 2 : Battery''' 1) Tape the two cells together for easier soldering 2) Take 2 wires, one red and one black, remove sleeving on their tips on a few centimeters 3) Soldering the 2 cells in parallel : black wire to the negative poles of each cell and red wire on the positive pole of each cell. ''(image 6)'' ''Caution:'' Isolate the welds (e.g. with tape) to avoid short-circuits . '''Module 3 : Voltage regulator and LED''' The voltage regulator has 2 inputs and 2 outputs: Inputs : VIN + and VIN - / Outputs : OUT + and OUT - 1) Take two wires (red and black). 2) Weld the red wire with the VIN+ input of the voltage regulator and the black wire with the VIN- input. The LED has two input wires : one positive and one negative. ''Caution:'' Wire polarity is not indicated on the LED. In order to identify it, use an ohmmeter. The wire is positive when it displays a null value. When it displays a higher value, the wire is negative. 3) Weld the LED's positive wire to the OUT+ output of the voltage regulator and the LED's negative wire to the OUT- output. ''(image 7)''ive wire to the OUT- output. ''(image 7)'')